Automatic Five Head I Shaped Hang Tag Attaching Machine
Automatic Five Head I Shaped Hang Tag Attaching Machine
The Automatic Five Head I-Shape Hang Tag Attaching Machine fixes hang tags onto products using five pinning heads that work at the same time. The operator loads the items, and all five heads drive I-shape tag pins in one cycle. It suits garment, sock, footwear, and accessory lines that pin high volumes daily and need far more output than a single hand gun can give.
| Specification | Value |
| Voltage | 220V, 50Hz |
| Efficiency | 1 cycle every 3 to 4 seconds |
| Fitness Tag Pin | Nylon Fine |
| Air Pressure | 0.4–0.8 MPa |
| Needles Length / Model | TN3709 |
Automatic Five Head I Shaped Hang Tag Attaching Machine
Product Overview:
Hand tagging one item at a time sets a hard limit on speed. Even a fast operator with an air gun can only pin one tag per pull. On a big export order with thousands of pieces, that single-point pace becomes the bottleneck for the whole packing area.
This machine breaks that limit with five heads. Each head drives an I-shape pin at once, so a single cycle tags five points instead of one. The operator lines up the products or tag positions, presses start, and all five pins set together. So output jumps several times over without adding staff.
Because the heads run on air, every pin goes in with the same force. The I-shape pins set straight and hold firm, and they do not tear soft fabric or card. Moreover, jams drop sharply, since the stroke no longer depends on how hard a worker squeezes.
The control panel lets you set head spacing and pin count for each job. So you can tag five separate items in one pass, or fix several tags on one large product. Just adjust the layout and call up the saved setting, and the machine matches the new order fast.
Buyers usually choose a five-head unit for one clear reason: volume. One operator here replaces a small team of manual taggers, and the pace stays steady from morning to night. That matters most on tight shipment deadlines, where slow tagging holds up the whole packing line.
The frame is built for daily factory use, and reloading pins takes only a moment per head. Needles and parts stay standard, so your team keeps every head running with little effort.
Product Features:
- Five pinning heads – Sets five I-shape pins in a single cycle
- Air-powered stroke – Each head drives its needle with steady force
- Adjustable head spacing – Set the gap to match the product or layout
- Programmable jobs – Store pin count and spacing per order
- Uniform pin force – Every pin sets straight and firm across all heads
- Fewer jams – Steady air stroke keeps pins from bending or sticking
- Standard pin clips – Feeds common I-shape tag pins, quick to reload
- Touch control panel – Set heads, count, and cycle on screen
- Safety guard – Protects the operator during each cycle
- Low maintenance – Standard needles and parts, fast to replace
Key Features:
1. Five-Head Simultaneous Tagging
All five heads drive I-shape pins in one cycle, so output rises several times over a single gun.
2. Consistent Pin Setting
Air gives the same force at every head, so each pin goes in straight and firm.
3. Higher Daily Output
One operator loads and starts the cycle, so a single station replaces a small tagging team.
4. Adjustable Head Layout
Set head spacing to tag five items at once or fix several tags on one product.
5. Fewer Jams and Bent Pins
The steady air stroke keeps pins feeding cleanly and cuts waste.
6. Quick Job Changeover
Saved settings recall pin count and spacing for each order in seconds.
7. Fast Reload
Standard I-shape pin clips load in a moment per head, so downtime stays low.
Frequently Asked Questions:
Automation cuts down manual handling, so each unit moves through the line faster. It also holds stitch quality steady from the first piece to the last. Because the machine doesn't get tired or lose focus, error rates drop and output stays consistent. Factories running our machines typically see lower labor costs too, since one operator can manage work that used to take several hands.
Yes. Naxtsew machines are built for continuous, shift-after-shift operation, not occasional use. If you're running a medium or high-volume apparel line, this is the kind of load they're designed for. Factories running two or three shifts a day rely on this same durability.
Our team provides setup guidance, operator training, and ongoing technical support. If a part needs replacing, we can supply it directly. So you're not left waiting on a third party once the machine is running.
Yes. We offer OEM and ODM options, which means we can adjust specs, tooling, and output speed to match your production line. Because every factory works differently, we start with your fabric type and volume needs before recommending a build.
We sell direct from the factory. This cuts out the markup you'd pay through a distributor, so you get factory pricing and direct support from our team. If you need parts, training, or service later, you're talking to us, not a middleman.
Lead times depend on the machine type and whether it's a standard build or a custom OEM/ODM order. [Insert your actual lead time range here — e.g., "4 to 8 weeks"]. Once you place an order, our team will give you a specific timeline based on your build.